M5POST
BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read

Go Back   M5POST - BMW M5 Forum > F10 M5 Forum > F10 M5 DIY Guides

Post Reply
 
Thread Tools Search this Thread
      09-10-2012, 07:31 PM   #1
IND Distribution
 
Drives: F10 M5
Join Date: Apr 2009
Location: Chicago, IL

Posts: 247
iTrader: (0)

IND Painted Reflector Installation Procedure

IND Painted Reflector Installation Procedure


Painted reflectors are among the first additions made by any owner of a modern BMW. The unsightly orange reflectors installed in cars bound for North America instantly break the smooth lines of BMW bumpers, and the F10 M5 is no different.

IND provides painted reflectors as a cost effective solution. We use OE BMW reflectors for a factory fit, and the same paint process we would use to repaint an entire car. Each reflector is sanded, prepped for paint, primed, then painted.

Many enthusiasts enjoy installing their own painted reflectors, so weíve created this installation DIY to help.

Tools needed:
  • 8mm socket and ratchet
  • Alcohol solvent or cleaner



First, turn the steering wheel to full lock, in any direction. This will expose the fender liner.





With the fender liner exposed, begin removing the 8mm screws near the front reflectors.



Slide your hand behind the fender liner, to access the back of the painted reflector. Youíll need to keep your hand on the back of the reflector to control itís movement as you remove it from the bumper.





Push on the face of the reflector. This will eventually release the adhesive backing on the reflector from the inside of the bumper, and will free the reflector. Be careful not to drop the reflector inside the bumper during this step, as it may come free suddenly! At this point you can remove the OE amber reflector.



Remove any remaining adhesive tape by peeling it from the inside of the bumper.



Soak a rag in an alcohol-based cleaner, and clean the inside surface of the bumper. This will prepare the area for a strong bond with the new adhesive.



Take the new IND painted reflector, and remove the film covering the adhesive tape.



Slide the reflector into the bumper. Be careful not to touch the adhesive tape during this step.







Align the reflector with itís opening, and press the reflector against the inside of the bumper. Hold the reflector for several seconds to ensure that the adhesive has a strong grip.

Thatís it! Now simply turn the wheel to full lock on the opposite side, and repeat the process.
IND Distribution is offline  
0
Reply With Quote
      11-27-2012, 06:26 PM   #2
Grayblack
Lieutenant
 
Grayblack's Avatar
 
Drives: M5 F10 Space Gray
Join Date: Nov 2012
Location: Orange County, CA

Posts: 417
iTrader: (0)

Here are my painted reflectors. Perfect color match by IND.
Attached Images
 
Grayblack is offline  
0
Reply With Quote
      01-31-2013, 07:11 AM   #3
Protious
Private First Class
 
Drives: 2013 BMW M5
Join Date: Nov 2012
Location: Texas

Posts: 155
iTrader: (0)

A much easier way to get the OE reflectors off is to use a credit card on the edge of the reflector inside the fender, that way you're getting directly to the tape instead of pushing on the reflector.
Protious is offline  
0
Reply With Quote
      09-30-2013, 10:09 PM   #4
savela
Second Lieutenant
 
savela's Avatar
 
Drives: 2014 M5
Join Date: Aug 2010
Location: TX

Posts: 235
iTrader: (0)

Their way works quite well. Simply place your hand back there and 'peel' the reflector off the inside of the bumper....requires very little pushing. These mods give a lot of bang for the buck!
__________________
2014 ///M5
2011 550i (traded)
savela is offline   United_States
0
Reply With Quote
      10-01-2013, 09:51 PM   #5
MELLOWYELLOW06
Captain
 
MELLOWYELLOW06's Avatar
 
Drives: 2013 535 MSport & 2012 650i
Join Date: Nov 2012
Location: Los Angeles

Posts: 840
iTrader: (0)

What size tape do you need once you remove stock

I got a painted set from s friend but it has no adhesive
MELLOWYELLOW06 is offline  
0
Reply With Quote
      10-18-2013, 03:34 PM   #6
eleven11
Captain
 
eleven11's Avatar
 
Drives: -F10 M5 ZCP-
Join Date: Mar 2007
Location: Derby City

Posts: 713
iTrader: (0)

Just completed the installation, and wanted to leave a few comments. It looks great, by the way (thanks iND ).

There are a total of 3 screws to remove:
1) Above the side camera (around the bottom of the reflector)
2) Below the side camera
3) Near the very bottom of the fender

The screws remove quite easily, so I simply used a small 8mm hand tool, rather than a larger ratchet to reduce unnecessary contact. Same with replacing them.

Finally, the OEM reflector was more stubborn than I was expecting during removal (not too bad, though). I wouldn't recommend it to any aspiring hand models. The key, for me, was slow steady pressure.
__________________

2014 M5 ZCP - Current
2011 135i Coupe - Retired
2007 335i Sedan - Retired
eleven11 is offline   United_States
0
Reply With Quote
      11-25-2013, 01:22 AM   #7
Spinny02
Captain
 
Spinny02's Avatar
 
Drives: 2014 M5
Join Date: Jun 2013
Location: Houston, Tx

Posts: 958
iTrader: (0)

Thanks 11. Did have to remove all three screws.

I also had to use the credit card / hotel rewards point card to help remover the pax side. The driver side was able to be pushed out. Both side left all the sticky, so I had to roll my finger down from top to bottom to get rid of all of it. Cleaned it up with a alcohol pad. Took about 20 min total for both sides.

The driver side is very even with the bumper and looks great. The pax side pokes out a bit more but still look good.
Attached Images
  
__________________
Spinny02 is offline   United_States
0
Reply With Quote
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 02:32 AM.




m5post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST