01-17-2015, 08:53 AM | #1 |
Private
25
Rep 55
Posts |
Brake Caliper & Rotor Removal on F10
Hi Guys.
I want to remove my brake calipers and rotors for painting/powder coating on my 2014 M5 CP with regular Breaks. I am going to ship the calipers to iND; the whole process might take few weeks. Since I am planning to do this in m y garage I am looking for advice I am very familiar with breaks of regular cars but not with M5, I am assuming they are all similar. Once the calipers and rotors are removed I will I seal/close the break lines. The car will be left on the stands for weeks, when I put the rotors and calipers back other than taking the air out do I need to do anything else? Like: Re calibrate the ABS? How about the rear electronic parking break, do I need to do anything special? Any advice, links for videos will be very helpful Thanks |
02-04-2015, 10:03 PM | #2 | |
Captain
169
Rep 687
Posts |
Quote:
o computer system is required. Make sure front wheels are blocked front and rear. With car jacked up and rear wheel removed, start the engine and release the handbrake button which will release the handbrake at the rear callipers. Turn off the engine. The handbrake will remain off. Off Side Rear Brake Pads Replacement Remove EMF brake actuator electrical cable by unplugging, release cable from bracket and unclip further back to move cable away from the work area. Detached EMF hand brake actuator by unscrewing 2 small torx bolts (star key bolts, not Allen key bolts); one of these bolts will hold the cable bracket, remove actuator from calliper. Rest actuator on suspension wishbone as it still has cables attached. Remove floating central section of calliper that contains the piston, by removing 2 x 13mm bolts that are bolted through to the 2 small rubber gators. Take care not to damage the pad wear sensor on the off side rear wheel. Rest this section on a tall item (wooden block or something similar) to avoid putting undue pressure on the brake hose. Remove brake pads sideways. On off side inner pad carefully release pad wear sensor with screwdriver (it just pops out). Remove metal shims and replace with new or if no new ones available clean up existing shims with wire brush and replace. Attach pad wear sensor to new inside pad and install into place, install outer pad. On central calliper at the rear of the piston where the actuator spline fits, turn spline clockwise with small tool until it comes to a stop (tried turning anticlockwise as advised by someone but ended up pushing piston out even further). Then use a pressure clamp and gently squeeze piston back into calliper body. Slide central calliper into position back over pads. Replace 2 x 13mm bolts and tighten. Offer up EMF hand brake actuator and align spline, when located correctly, actuator will be flush to rear of calliper. Replace cable bracket, replace and tighten 2 x torx bolts (star key bolts). Re-plug actuator cable to actuator. Replace actuator cable and pad wear cables into bracket. Re-clip cable further back. Replace wheel and lower to ground. Near Side Rear Brake Pads Replacement Repeat procedure for near side brake pads replacement. Note that there is no pad wear sensor on this side, therefore when the EMF handbrake actuator is unbolted it can be removed and laid on the ground. Continue to follow the above procedure. Handbrake and footbrake operation When pad replacement is complete and car is on ground, press footbrake pedal a few times. With foot on footbrake, start car and activate handbrake button a few times which will set EMF brake into working order. With handbrake released you will find the brake auto hold also works correctly. Job is complete. Now for a test drive. |
|
Appreciate
0
|
02-08-2015, 05:59 AM | #4 |
First Lieutenant
72
Rep 315
Posts
Drives: 13 AWSO M5,16 DGMR X5M
Join Date: Jul 2012
Location: Indonesia
|
most important part is to bleed the brake fluid.. Be careful with the excess of brake fluid spilled..
__________________
2012 Rosso Mars Lamborghini Gallardo STS LP570-4
2013 AW SO F10 M5 upgrades: RKP front spoiler, M performance carbon spoiler, 3D design rear carbon diffuser, KW HAS Sleeve Kit, Akrapovic Evolution Carbon tips, ind black LCI front and rear grills, GruppeM RAM intake, 20" HRE P104 satin charcoal with PSS tires) |
Appreciate
0
|
Post Reply |
Bookmarks |
|
|