BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read

Go Back   M5POST - BMW M5 Forum > M5 Classifieds > Sponsors Classifieds

Post Reply
Thread Tools Search this Thread
      10-08-2013, 02:51 PM   #1
GMP Performance
Lieutenant Colonel
GMP Performance's Avatar

Drives: E90 M3, E82 135i, E90 325i
Join Date: Aug 2009
Location: Charlotte, NC

iTrader: (1)

UUC Shifter Kit Special: 15% off AND Half Off Installation from GMP Performance

Nothing that can make every drive more satisfying like the "snick-snick" feeling of a precision shifter. Too bad BMWs are not known for that, and that is where UUC Motorwerks steps in. UUC's design focuses on precision-machined pieces, "massive overkill" designs, race testing and the finest of materials, all combined into a short shifter kit that's hard to beat. To help you get all the advantages of UUC's shifter kits, we are offering a special, just for you guys. For a limited time, get 15% off of the part and HALF OFF installation! If you want all the advantages of a short shifter at a fraction of the cost, contact us now!

About the UUC Short Shifter for the M5

UUC's years of shifter experience and continual development have resulted in a major upgrade to our product, the all-new EVO3.

What's new with EVO3? Everything.

Every part of the EVO3 has been changed from EVO2. Superficial appearance shows little difference, but every internal component, dimension, and hardware piece has been changed. While keeping within the basic design of the earlier EVO2, the EVO3 is as close to a "clean sheet" design as possible.

Important upgrade points:

Subjectively 20% effort reduction compared to EVO2, very close to stock effort feel. This is accomplished by a complete reconfiguration of lever dimensions, linkage geometry, and all friction and pivot points in the assembly.

This results in the smoothest and least-notchy shifter available. Due to the increased precision and smoothness of the assembly, shift effort is only slightly increased over the original BMW setup.

The exact same 35% reduction in shift travel (100mm from 3rd gear to 4th gear total travel) is retained at stock height, and down to over 40% when height is adjusted to the short end of the adjustment range.

Completely self-contained and self-adjusting primary pivot bearing assembly. Unlike the original BMW pivot bushing cup setup, our new bearing system is not open to outside contamination (underside of the car in the BMW shifter assembly is exposed to road dirt) and will retain lubrication, keep out the grit that "roughens" a shifter feel over time (and destroys plastic ball pivots like the OE and many aftermarket units), and positions the shifter assembly perfectly for ideal linkage alignment.

New full-length internal vibration absorbing material that surpasses any OE or aftermarket material for longevity and retention of design specifications.

New standard lower pivot bearing setup with enhanced ease of installation.

To find out more about the UUC Ultimate Short Shifter Kit, click here or contact us!

Trey @ GMP Performance
Phone: 704-525-0941 x 254
Email: trey@gmpperformance.com
Website: www.gmpperformance.com
Appreciate 0
Post Reply


gmp performance, short shifter, uuc

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -4. The time now is 12:00 PM.

Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST