10-26-2014, 10:24 AM | #45 | |
You got my money?
3620
Rep 4,849
Posts
Drives: Ice Cream Truck
Join Date: Jul 2011
Location: ///OC
|
Quote:
__________________
2022 G80 M3 Competition X /// 2025 X5 40i X
|
|
Appreciate
0
|
11-19-2014, 08:40 PM | #46 | |
You got my money?
3620
Rep 4,849
Posts
Drives: Ice Cream Truck
Join Date: Jul 2011
Location: ///OC
|
Quote:
That tunnel is actually the rear air flow path. I would NOT DO THIS if your an older build. |
|
Appreciate
0
|
11-19-2014, 09:03 PM | #47 | ||
Lieutenant Colonel
125
Rep 1,840
Posts
Drives: '14 M5 CP Dinan Stage 2
Join Date: Jun 2013
Location: Houston, Tx
|
Quote:
__________________
|
||
Appreciate
0
|
11-21-2014, 05:47 PM | #48 |
First Lieutenant
70
Rep 327
Posts
Drives: 2017 Tesla Model X P100D
Join Date: Oct 2012
Location: Menlo Park, CA
|
I don't believe this. There wouldn't be a carpet with holes in it with air running down it. There would be a proper plastic air duct supplying air. What is your source and evidence for this statement?
|
Appreciate
0
|
11-21-2014, 08:47 PM | #49 | |
You got my money?
3620
Rep 4,849
Posts
Drives: Ice Cream Truck
Join Date: Jul 2011
Location: ///OC
|
Quote:
I cut mine to install the new cup holder. Whatever I cut looked like a plastic tube. Once I was done, I turned heater on full blast and my cup holders got super warm and I heard plastic fragments run down my center console from my shifter to my rear seat HVAC. Where the plastic bits sounded like they got sucked into the rear fan and shot out. So I assumed I cut into a air/heat tube. Today I ran my AC and my cup holder was cold and blowing air out of the fingers. You tell me...
__________________
2022 G80 M3 Competition X /// 2025 X5 40i X
|
|
Appreciate
0
|
11-25-2014, 10:11 AM | #50 |
Lieutenant Colonel
117
Rep 1,625
Posts |
LCI cupholders blow in the first place, not sure why anyone would even bother switching to a slightly better, but equally shit solution
__________________
2014 Individual /// M5 Competition AW/AB || Vorsteiner FF-103 || BMS JB4 || Meisterschaft GTC || RPI || IND || Challenge || |
Appreciate
0
|
11-25-2014, 10:26 AM | #51 | |
Private
14
Rep 91
Posts |
Quote:
|
|
Appreciate
0
|
11-25-2014, 10:39 AM | #52 | |
Lieutenant Colonel
125
Rep 1,840
Posts
Drives: '14 M5 CP Dinan Stage 2
Join Date: Jun 2013
Location: Houston, Tx
|
Quote:
__________________
|
|
Appreciate
0
|
03-05-2019, 09:29 PM | #56 |
New Member
3
Rep 17
Posts |
I think the more important issue we need to solve is how do we get the fingers to stay retracted ? This would make the holder able to fit a much larger size cup.
I can't get my protein shaker cup in them and it is killing me ! |
Appreciate
1
Rennyk.126.50 |
03-06-2019, 08:33 AM | #57 |
Banned
277
Rep 541
Posts |
be wayyy easier to just find a protein shaker that fits
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|