05-06-2020, 01:23 PM | #177 |
Banned
200
Rep 300
Posts |
|
Appreciate
0
|
05-07-2020, 02:36 AM | #178 | |
New Member
8
Rep 16
Posts |
Quote:
I did it without jacking up the car. I just drove up on some wood planks 1.5 inches thick. It wasn't enough so i jacked each side up and placed 2x4's under each as well so about 3 inch left and I was able to complete the job laying on my back. Step one is unbolt grounding straps. Then start cutting. At first the dimples in the factory exhaust were not as noticeable as I thought they would be but once found a Sawzaw made pretty quick work of the exhaust piping. From there spray the hangers with WD40 let it sit a min. Pull the mufflers off and disconnect the vacuum tubing. Install of the SOUL system was easy the whole thing took me about 2 hours. The hardest part is figuring out which depth I wanted the tips at. I would say I spent about an hour or so just messing with different set ups. The Soul Exhaust sounds good. Deep but not like an American muscle car. When you are just cruising around it isn't annoyingly loud. When you get on the gas though she really screams. The workmanship on the system is great. Welds are super clean fit and finish is perfect. Now if only Soul made a cold air system and upgraded air chargers. =)
__________________
2014 F10 M5 Competition package.
20 in Asanti ABL-I3 Vega Soul Exhaust future mods: Cold air intake, down pipes, tune |
|
Appreciate
3
|
05-07-2020, 09:21 AM | #179 |
Banned
200
Rep 300
Posts |
Awesome, thank you for the review - glad you are happy!
While our focus is exhaust, we have a lot of partners in the industry and offer many third party components to enhance your setup, just let us know what you need! -Mike |
Appreciate
0
|
05-13-2020, 08:09 AM | #180 |
Private First Class
71
Rep 199
Posts |
Have you guys ever thought about titanium tips (with the burnt finish)? Just curious. I have been doing some homework on exhausts and it appears this car really just needs an axle back.
|
Appreciate
1
|
05-13-2020, 08:32 AM | #181 |
Banned
200
Rep 300
Posts |
|
Appreciate
0
|
05-14-2020, 02:00 PM | #182 |
Banned
200
Rep 300
Posts |
We always consider our existing products for continued improvement. We've made strides in our bending capabilities and will be eliminating a weld from each pipe for an even better product! We're also continuing to look into a cast Y section that offers great flow without being too heavy.
-Mike |
Appreciate
0
|
06-01-2020, 01:53 AM | #184 |
Captain
382
Rep 948
Posts |
|
Appreciate
1
|
06-03-2020, 03:18 PM | #185 |
Banned
200
Rep 300
Posts |
|
Appreciate
0
|
06-19-2020, 03:07 PM | #187 | |
Extruding Elements
517
Rep 535
Posts
Drives: 2016 BMW M5 Comp
Join Date: Feb 2020
Location: Florida
|
Quote:
Before rev After start No after rev...this would of completed the puzzle...
__________________
2022 Yukon XL AT4
2016 BMW M5 2015 Ford F250 Super Duty 2006 BMW M5 |
|
Appreciate
0
|
06-19-2020, 03:17 PM | #188 |
Extruding Elements
517
Rep 535
Posts
Drives: 2016 BMW M5 Comp
Join Date: Feb 2020
Location: Florida
|
"Soul Performance Products has exceeded their stored private messages quota and cannot accept further messages until they clear some space"
nooooooo....MONICA!!!!
__________________
2022 Yukon XL AT4
2016 BMW M5 2015 Ford F250 Super Duty 2006 BMW M5 |
Appreciate
1
|
06-22-2020, 08:58 AM | #189 |
Banned
200
Rep 300
Posts |
|
Appreciate
0
|
06-24-2020, 04:05 PM | #190 |
Banned
200
Rep 300
Posts |
In conjunction with a weld elimination in May, we're finally rolling out our cast Y section! This will yield better interior flow with the smooth wall path and edged interior. The thicker walls may yield a very slight increase in drone reduction.
We thank everyone for supporting us and in turn we'll continue to refine present and future products. -Mike |
Appreciate
0
|
06-25-2020, 11:39 AM | #191 |
First Lieutenant
396
Rep 336
Posts |
so much want.
seems like the perfect solution for me because the rest of the exhaust isnt worth replacing. waiting for brakes to show up first. one thing at a time. ha. |
Appreciate
2
Cylenterok136.00 |
06-25-2020, 03:18 PM | #192 |
Banned
200
Rep 300
Posts |
|
Appreciate
0
|
07-09-2020, 10:20 PM | #193 |
Banned
1158
Rep 545
Posts
Drives: 2015 M5 CP - 2022 M5 CS
Join Date: Sep 2016
Location: Phoenix
|
Ordered a black PVD single wall slash cut kit, excited for its arrival!
Thanks a bunch Mike for the assistance! Can’t wait to see the new cast collector in action |
Appreciate
1
|
07-24-2020, 09:28 AM | #196 | |
Merlin
487
Rep 730
Posts
Drives: 2012 BMW M3 6MT w/ZCP
Join Date: Feb 2014
Location: United States
|
Quote:
Thank you, Merlin
__________________
2012 E92 M3 ZCP | 2008 E90 335xi | 2008 E90 335i | |
|
Appreciate
0
|
07-27-2020, 11:57 AM | #197 | |
Banned
200
Rep 300
Posts |
We are looking for a local 550i to adapt our system, but as it stands you would need the M5 rear lower valance for it to work and some adjustment might be needed. We have had people do it.
Quote:
Below you see three welds that look very similar on the outside – but inside it’s a very different story! Proper TIG welding technique is not just about achieving a great stack of dimes on the outside of the piping, but more importantly about penetration and preservation – making sure the back of the weld is functionally sound. Back purging is the process of shielding the inside of the weld with an inert gas to prevent contamination during the welding process, resulting in a stronger weld. Wikipedia extrapolates on this statement: “Stainless steels, duplex steels, titanium-, nickel- and zirconium- alloys are sensitive to the presence of air, oxygen, hydrogen, water vapour and other vapours and gases that may combine with the hot metal as it is being joined. Such gases may combine with the metal to form undesirable compounds that may reduce corrosion resistance or may be instrumental in creating cracks or other structural defects in metals.” The rate of oxidation in metal progresses more rapidly as temperature increases – to a very high level during welding. Back purging prevents this from happening. An inert gas does not undergo chemical reactions and prevents rapid oxidation while the stainless is in a molten state. Argon, a noble gas, is the most commonly used shielding gas in TIG welding. It offers a very stable arc allowing a skilled fabricator great control over the resulting weld. As part of the welding process, the welding torch is designed to emit shielding gas to protect the front of the weld. Different cups offer different gas patterns as seen below in a still below from a demonstrative video, but ultimately the goal is to shield the weld from oxidation and the negative effects explained above. This is how you can have a weld that looks great on the outside with the interior of the welding looking much different. To protect the inside of the weld, back purging is necessary – but not always done. Here’s an example of SOUL using back purging during the fabrication process. Our fabricator has plugged the ends of this 991.2 Carrera Cat Bypass Pipe and Argon gas is being pumped from a gas cylinder at a controlled rate through the inside of the piping. It takes some time to displace the ambient air with the inert gas before the welding can begin. Now that you’re aware of what back purging is and why it’s done, let’s go over a few examples of different welding scenarios with and without it to give you a better idea of why it is used. Weld 1: Lack Of Penetration (No Back Purging) This butt weld shows a lack of full penetration, leaving the root gap exposed. During the welding process this gap can allow for a better, stronger weld. Left unfilled, it can attract moisture and corrode quicker than the rest of the exhaust system. Without full penetration in this butt joint, this is a weak weld with reduced strength – it’s a point of failure. Below is an example of weld that failed from lack of full penetration. This weld can result from high amp / low duration settings with no back purging. The blackened surface consists of oxides of chrome, iron, and nickel – effectively the rust resistant properties of the stainless steel are being burnt out of it. Weld 2: Sugaring (No Back Purging) Sugaring / granulation / contamination is extreme oxidation of the back side of a stainless weld. This weld has penetration but is also heavily oxidized due to lack of a shielding gas. While this weld has full penetration it is not as strong as a back purged weld and is also a point of potential rust and / or failure under stress. To a mild effect sugaring also interrupts exhaust flow. Sugaring is often a rejectable defect in medical / food industries as the texture can trap bacteria. Weld 3: Back Purged Weld In the end strength, longevity, and minimal impact of flow are the end goals of a back purged weld. This weld was done with the same settings as the weld above but was back purged with Argon. The inert gas prevents burning and contamination for a visibly different weld. There is full penetration with no contamination on the backside. Not only is it beautiful and well done, but it is quite strong. We’re proud to weld to the highest possible standards by back purging our welds whenever possible and we’re proud to incorporate Airgas ARCAL™ Prime argon into the process. Argon is an excellent shielding gas and is available in many blends for back purging. Airgas ARCAL™ Prime has an extremely high purity at 99.998% Ar with H2O<10ppm. This increases our internal cost of producing components but results in the best possible weld, and the best possible welds result in the smoothest flow and the best durability. Our commitment to quality and excellent customer service is considered in as many aspects of how we business as possible – every detail matters – even .001 percent of a gas. -Mike |
|
Appreciate
4
|
07-29-2020, 12:36 PM | #198 |
First Lieutenant
396
Rep 336
Posts |
Learned something here. Great reply.
|
Appreciate
1
|
Post Reply |
Bookmarks |
|
|