05-04-2024, 05:19 PM | #1 |
New Member
14
Rep 20
Posts |
F10 M5 Bootmod3 E30 dyno numbers are here
Hello everyone today I'm showing you my dyno number from my most recent run i hope this helps you guys be able to see where your car is in terms of mods and to see the potential of getting a ots tune from bootmod3 because i searched everywhere any could not find any whp numbers.honestly the results really surprised me I didn’t think I would make that type of horsepower and torque.
Mods -vrsf cattless down pipes -gamma project front mount intakes -ngk 2 step colder plugs gapped to 0.20mm -BM3 ots stage 2 e30 tune aggressive burbles link to video- |
05-09-2024, 09:44 PM | #4 |
Private First Class
120
Rep 138
Posts |
Graph looks great from what we can see in the video!
Torque is probably limited to protect the DCT, you don't really want to go much higher than 650 from everything I've read. I'd love to see you 1/4 mile trap speed
__________________
Currently: '15 M5 (dct) BM3 STG1 11.3@128 Spinning /// '11 X3 35i 13.9@99/// '02 Transam 12.7@112
Previously: '15 M3 (dct) BM3 11.58@126 /// '13 Cadillac CTS-V 11.9@115 /// '12 128i /// '08 Benz c300 6spd |
Appreciate
1
ghanii14.00 |
05-13-2024, 06:08 PM | #5 |
New Member
14
Rep 20
Posts |
Honestly, the car feels great, and has power throughout the entire RPM. I don’t run MDM mode I have found to have slower times in MDM mode compared to normal traction mode,however I do completely turn off traction when I’m doing roll races and I only start from 60mph I usually will hook up.
|
Appreciate
0
|
05-13-2024, 06:11 PM | #6 |
New Member
14
Rep 20
Posts |
Yeah, torque is limited to 661 foot pounds. It reaches max torque at around 3500 RPM and starts to taper off further on. I haven’t had much clutch issues because I run an XHP stage three tune that increases the clutch line pressure to almost 20 bar so i haven’t ran into any shifting issues or clutch slip issues. I just bought a draggy so I’ll post the numbers on this form as soon as I get them.
|
Appreciate
1
TrueNorthM5119.50 |
05-13-2024, 08:37 PM | #7 | |
Lieutenant Colonel
605
Rep 1,514
Posts |
Quote:
|
|
Appreciate
1
ghanii14.00 |
05-13-2024, 08:48 PM | #8 |
New Member
14
Rep 20
Posts |
No not yet I was looking at the transmission data and as of now I don’t think it needs it honestly, I prefer having the torch punch because one problem with these cards that I have learned is that when you’re doing a 60 and you are not break boosting it does take a little bit to break out because of how heavy you are but you make it back up in the top end
|
Appreciate
0
|
05-13-2024, 09:20 PM | #9 | |
Lieutenant Colonel
605
Rep 1,514
Posts |
Quote:
|
|
Appreciate
0
|
05-16-2024, 03:25 PM | #10 |
Private
25
Rep 76
Posts |
Just curious is it must that I run e30 with this tune. What if I run e20 with this tune. Will it still work ok or I can only run e30 with this. Asking as want to be safe from the fueling side.
Thanks
__________________
2013 M5, Bootmod 3 stage 2 91 octane, Evolve Catless downpipes
2013 Activehybrid 3, Pure stage 2 turbo with High flow inlet and Dv upgrade, Wagner Evo 2 comp intercooler, ER charge pipes, BMS JB4, BMS intake, BMS Meth kit with a single cm7 nozzle, Fuel it Port injection in 550cc injectors platinum kit with Ethanol analyzer, Fuel it stage 2 LPFP, ER oil cooler kit, Mach v Valvetronic exhaust, Bootmod 3 and running E20 |
Appreciate
0
|
05-16-2024, 04:31 PM | #11 | |
New Member
14
Rep 20
Posts |
Quote:
To summarize if you have a tune that is designed for E30 or more and you put less than the desired amount you may experience misfires. |
|
Appreciate
1
vigilante24.50 |
05-16-2024, 05:31 PM | #13 |
New Member
14
Rep 20
Posts |
Thank you, I run 10w40 Valvoline VR one synthetic and I use liquid Molly, ceratec honestly it’s the best set up I’ve found I ran the same set up a lot when I had a 2007 Bmw 335i that made 620whp on stock motors and pure turbos and I never blew up that motor I think the most important thing is how often you do your oil changes I do my oil changes every 2000 to 2500 miles I know that seems excessive but I’ve always lived by the thought process of oil is cheap engines are not.
|
Appreciate
0
|
05-16-2024, 06:03 PM | #14 | |
Lieutenant Colonel
605
Rep 1,514
Posts |
Quote:
|
|
Appreciate
0
|
05-16-2024, 06:18 PM | #15 |
New Member
14
Rep 20
Posts |
On a empty gas tank I put about 6.1 to 6.5 gallons of e85 and about 13 to 14 gallons of 91oct keep in mind I live in the state of California where my gas is garbage if you live somewhere that has access to 93 octane, your mixture will be different. You will probably be using less ethanol. I always recommend using an E 85 calculator just in case the one that I use is called “e85Cal” it’s on apple App Store I don’t know if it’s on android. When you do your calculations set your ethanol percentage at the pump to E70 this is the average that you get from gas stations unless you’re using gas companies like VP racing gas or Ignite red e85 where as those companies ethanol is 100%, e85.
|
Appreciate
0
|
05-17-2024, 12:57 AM | #16 | |
Private
25
Rep 76
Posts |
Quote:
Thanks
__________________
2013 M5, Bootmod 3 stage 2 91 octane, Evolve Catless downpipes
2013 Activehybrid 3, Pure stage 2 turbo with High flow inlet and Dv upgrade, Wagner Evo 2 comp intercooler, ER charge pipes, BMS JB4, BMS intake, BMS Meth kit with a single cm7 nozzle, Fuel it Port injection in 550cc injectors platinum kit with Ethanol analyzer, Fuel it stage 2 LPFP, ER oil cooler kit, Mach v Valvetronic exhaust, Bootmod 3 and running E20 |
|
Appreciate
1
ghanii14.00 |
05-18-2024, 04:52 AM | #18 |
Second Lieutenant
226
Rep 257
Posts
Drives: 2013 w/ DPs, BM3 stage 2
Join Date: Sep 2022
Location: Tampa Bay area Florida
|
Nice ride. My car's about the same but on stage 2 93 octane OTS map and stage 2 xHP. I had a klown at a shop last week try to tell me BM3 is junk and blocks codes from the DMEs.
|
Appreciate
1
ghanii14.00 |
05-18-2024, 09:11 AM | #19 |
New Member
14
Rep 20
Posts |
Yes, you should not need to upgrade your fuel system however, running ethanol does put more strain on your fuel pump. Always recommend every once in a while to do a data log to check your low pressure fuel pump.
|
Appreciate
0
|
05-18-2024, 09:20 AM | #20 |
New Member
14
Rep 20
Posts |
I look at it like this BM3 has been making and perfecting this tune for a long time I doubt that they do that type of stuff, now I can confirm they do disable emission monitoring parameters for the catalytic converter and oxygen sensor. However, that will not affect the car being able to detect issues you’re still receive the drive ability codes. also as a technician as well I’m sorry to hear that. Honestly, I think the guy was just scared to work on the car because he’s probably not familiar with working on tuned vehicles. sometimes peoples pride as technicians come into play and they make the rest of us look bad.
|
Appreciate
1
KurtsM5226.00 |
05-19-2024, 07:01 AM | #21 |
Second Lieutenant
226
Rep 257
Posts
Drives: 2013 w/ DPs, BM3 stage 2
Join Date: Sep 2022
Location: Tampa Bay area Florida
|
The jerk also laid some fresh drags from a dig in my car when he "test drove" it. I know he did it a 1/2 block from their shop(I saw them and was wondering WTF, and because sand was stuck to my tires after I drove 9 miles home. Sand only sticks to melted rubber. And yeah, he has a MHD 335 LOL.
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|